Assembled Wi-Fi model
ESP32-S3 N16R8 Wi-Fi AI Voice Assistant
Price per unit
$49.00 NZD
5 in stock
An assembled desktop AI voice assistant with 2.4 GHz Wi-Fi, a 1.54-inch colour TFT display, a speaker and a rechargeable battery in a clear enclosure. Use the buttons to adjust the volume, start listening or switch to standby. The USB-C port supports charging and firmware flashing, and a spare UART is available for hardware projects.
1.54-inch colour TFT · USB-C
Tap a method to pre-select it at checkout. Stock is reserved when you place your order.
Buttons and controls
Listening… - Power
Press once to turn the device on. Press again to turn it off.
- Volume down
Press to lower the volume.
- Listening / standby
Press to start listening. Press again to return to standby.
- Volume up
Press to raise the volume.
Mainboard layout
The 40 × 40 mm PCB has 36 mm vertical spacing between the mounting holes shown. The supplier diagram marks R1.6 mm at the upper-right corner.
- Status LED
- Microphone opening (keep clear)
- 4G module interface
- Boot button
- Volume up button
- ESP32-S3R8 chip
- Microphone
- 4G module interface
- USB-C for charging and flashing
- Volume down button
- Speaker connector
- Power button
- Battery connector
- Spare serial (UART) interface
The 4G module interface is shown for board reference. This assembled model connects over Wi-Fi.
Technical specifications
- Display
- 1.54-inch colour TFT
- Processor
- Espressif ESP32-S3R8
- Memory configuration
- N16R8 · 16 MB flash and 8 MB PSRAM
- Connectivity
- 2.4 GHz Wi-Fi
- TFT connection
- 10-pin connector for an ST7789 display
- Dimensions
- PCB 40 × 40 mm · enclosure 41 × 41 × 30 mm
- Battery life
- About 2.5 hours of continuous conversation at maximum volume or 9 hours on standby (supplier estimates)
- Charging
- USB-C
- Firmware flashing
- Through the same USB-C port via the onboard CH340K USB-to-serial chip
- Voice wake-up
- Supported with compatible firmware
- Expansion
- One spare serial (UART) interface
- Battery connector
- ZH1.5
- Speaker connector
- MX1.25
- SKU
- esp32-s3-wifi-ai-voice-assistant
Board features
The ESP32-S3-based board supports voice wake-up with compatible firmware.
Use the spare UART connection to add hardware or develop your own firmware integrations.
What you can do with it
Start by simply talking to it. When you’re ready, link it to your smart home or build it into your own projects. Each step below says what you’ll need.
Start by talking to it
You’ll need: Your home Wi-Fi and a voice service set up on the device. Answers come from the AI service, so double-check anything important.
- A desk buddy that talks back
Have a yarn, ask for a joke or a fun fact, and give it a personality that suits you (see below).
- Homework and curious questions
Kids can ask things like “why can’t kiwi fly?” out loud and hear a spoken answer.
- Speaking practice
Practise everyday spoken English, or another language your voice service supports, at your own pace.
- Hands-free help in the kitchen or shed
Ask for a unit conversion or a quick explanation while your hands are covered in flour or glue.
Link it to your smart home
You’ll need: Home Assistant or a similar system, plus a voice service that can connect to it.
- Voice control for lights and plugs
Say “turn off the lounge light” to switch devices your smart home system already controls, such as certified smart plugs.
- Check on the house
Ask whether the garage door is shut or how warm the bedroom is, using sensors already connected to Home Assistant.
- Check on a 3D print
If your printer is connected to Home Assistant, ask how long the current print has left.
Build your own projects
You’ll need: A second ESP32-S3 board, the sensors for your project, and your own code or firmware changes. These are projects for makers who like to tinker.
- Greenhouse or tunnel house check-ins
A sensor board in the greenhouse measures temperature and humidity and sends the readings over Wi-Fi. The voice assistant stays inside the house, so you can ask “how warm is the greenhouse?” or set it to speak up when it gets too hot or cold.
- Frost warning by the bed
Put a temperature probe at plant height in the garden, orchard or lifestyle block and set the assistant to speak up when it drops towards freezing. Use it as an extra early warning, not as a replacement for a professional frost alarm.
- Water tank level on request
If you are on tank water, a level sensor on the tank lets you ask how full it is without walking out to check. The tank needs a Wi-Fi signal.
- Print a dock, case or little robot
Print a PETG stand for your desk, or connect a servo controller to the spare serial port and build a little robot that nods or waves.
Need parts? See our ESP32-S3 development board and ESP32-S3 project ideas for New Zealand homes and sheds.
Good to know before you buy
- Apart from the microphone, there are no sensors built in. Projects that measure temperature, water levels or doors need a separate board and sensors.
- Connects over 2.4 GHz Wi-Fi only, so it needs a Wi-Fi signal wherever you use it. The board has a 4G module interface, but this assembled model is the Wi-Fi version.
- Made for indoor use. The clear case is not waterproof, so keep it out of the rain and out of strong sun for long periods.
- The battery lasts about 2.5 hours of continuous conversation at full volume, or about 9 hours on standby (supplier estimates). For all-day use, keep it plugged into USB-C power.
- Not a safety device. Do not rely on it as your only frost, fire, security or medical alarm.
Voice features, supported languages and AI services depend on the firmware and service you configure.
Customise the assistant’s personality
With compatible software, write a short character description to guide how your assistant responds.
- Gentle
- Funny
- Calm and dignified
- Shy
- Straightforward and innocent
- Quick-tempered
Guides and project ideas
More ESP32-S3 boards and accessories
Each is sold separately. Check connectors and compatibility on the product page.
From our customers
Customer Reviews
No reviews yet
Reviews from verified buyers. Honest feedback, positive or negative, is welcome.
Write a review
Purchased this product? Open the private review link in your order email to verify your purchase automatically.
Need an invitation? Contact us using your order email. No account is required.